|
Post by usbbdm on Jul 2, 2005 22:18:25 GMT -5
USB BDM 0.5 has put on the network for you to download. This is the first version that extracts the DCT testing to a DLL. Also the flash chip support also moved to a DLL. In the future newer version of flash chip dll can be added to allow support more flash chips. It is possible for all the MC68331 target benefit the USB BDM software since now the UI is configurable. The existing DCT users still can gain the same function as before. www.geocities.com/dctbdm/exe/usbbdm.zipFor DCT tester www.geocities.com/dctbdm/exe/DCTTest.zipV0.45 still can be downloaded at www.geocities.com/dctbdm/exe/dctbdm.zip
|
|
|
Post by usbbdm on Jul 5, 2005 15:23:47 GMT -5
Has anybody uses 0.5. Is there any issues? For existing user, the first time you need do a little setup. I hope everybody move to 0.5. In the future, each module will be upgraded separately.
|
|
|
Post by patsfan on Jul 7, 2005 20:40:59 GMT -5
seams to work fine so far. haven't had a lot of time to use it lately. loading the module is no biggie, quite simple.
|
|
|
Post by srgrounds on Jul 8, 2005 0:53:35 GMT -5
Can you post a pic of the software, the way it should look when installed right? Thank you. Im having a hell-of-a-time with this.
|
|
|
Post by usbbdm on Jul 8, 2005 11:06:46 GMT -5
Here is a picture of a configured for PH8 testing. Here is a picture of config. If you do not see anything under "Target select" and you want to do DCT test, go to Tools->Load testing Module and select DCTTest.dll.
|
|
|
Post by srgrounds on Jul 8, 2005 18:49:17 GMT -5
I have asm tab, but i dont have code,nvram,ram tabs at bottom of top screen. At top i have all four tabs. When i type in reset 1 i get all the right info but when i type in init i get nothing. My config is all blank. Thanks for posting pic.
|
|
|
Post by usbbdm on Jul 8, 2005 21:09:38 GMT -5
I have asm tab, but i dont have code,nvram,ram tabs at bottom of top screen. At top i have all four tabs. When i type in reset 1 i get all the right info but when i type in init i get nothing. My config is all blank. Thanks for posting pic. You need to load DCTTest.dll. Go to Tools->Load...
|
|
|
Post by srgrounds on Jul 9, 2005 5:37:38 GMT -5
ok i did that, and across the top i got file, tools, dctestinbg, help. at bottom i still only have asm tab and nothing else. when i click on the dct tab it has a drop down with eight commands in it. but still missing tabs at bottom. running xp here.
|
|
|
Post by makaveli on Jul 9, 2005 8:21:29 GMT -5
where it says target drop down and select your type box.
|
|
|
Post by adrianbv6 on Jul 9, 2005 10:55:18 GMT -5
over in that image it shows
|
|
|
Post by adrianbv6 on Jul 9, 2005 10:55:56 GMT -5
you must load the DCTtesting dll first
|
|
|
Post by srgrounds on Jul 9, 2005 13:23:12 GMT -5
Got it going people, thanks for all your help. Real noob here. Saved firmware and nvram. Now what the hell do i do with it?
|
|
|
Post by usbbdm on Jul 10, 2005 10:27:25 GMT -5
DCTTest.dll 0.11 has been uploaded. Main changes is to add the clear PPV for test purpose. Not gaurantee work. Report any problem. Also add the CR4 to the test target.
Known problem on CR4. The "break" command does not work on one of the CR4 board. It could be the hardware connector on the board is a little different than other boards.
|
|
|
Post by usbbdm on Jul 11, 2005 9:40:57 GMT -5
USB BDM 0.51 released. www.geocities.com/dctbdm/exe/usbbdm.zip1. Significantly improved the read/write memory speed. (3X faster). 2. Automatically load test dll when test dll is located at the same directory. (Many feedback on the difficulty to load the test dll)/
|
|
|
Post by patsfan on Jul 11, 2005 14:00:25 GMT -5
excellent. i will take a look later
|
|
|
Post by usbbdm on Jul 12, 2005 22:08:12 GMT -5
|
|