|
|
Post by usbbdm on Feb 18, 2005 17:58:00 GMT -5
1. Upload the firmware to PC use BDM.
2. Disassemble the firmware.
3. Find the entry of the clear PPV.
4. Use BDM command to excute the entry. You might need to disable the interrupt.
5. Go to diagnostic to check the PPV memory.
|
|
usb2
New Member
Posts: 1
|
Post by usb2 on Feb 18, 2005 18:09:13 GMT -5
How can I find clear PPV function entry pointer address from a disassemled code? And how to go to the diagnostics menu?
|
|
Angus
New Member
Posts: 1
|
Post by Angus on Feb 19, 2005 12:40:44 GMT -5
To get to the diagnostic menu turn the unit on wait 5 seconds then turn it off and then push select.
|
|
|
|
Post by jake34j on May 29, 2005 16:34:21 GMT -5
Is it true that if you press the button on the SW100 that this will erase the PPV memory as well?
|
|
|
|
Post by patsfan on May 29, 2005 20:17:48 GMT -5
never tried, but i would say no. that would be too easy. i'm not sure what the switch is for it acts like a reset switch does the same as pulling the power cord.
|
|
|
|
Post by adrianbv6 on May 31, 2005 0:56:26 GMT -5
nothing on the board or pressing butons can erase ppv thats a normal reset button
when you purchace a program the firmware of the box write the nvram and writes the nvram .....to clear it u can do it by restoring the clean nvram and firmare or otherwise......company sends a signal back to the box afther they read the purchaces and they go back to 0
|
|
|
|
Post by patsfan on May 31, 2005 5:22:19 GMT -5
nothing on the board or pressing butons can erase ppv thats a normal reset button would have been nice though, eh?  |
|
pete
New Member
Posts: 7
|
Post by pete on Jun 11, 2005 8:30:44 GMT -5
OK, A little help around here.. My PPV NOT been cleared..
This are my steps..
(yes I did back up nvram the first time) do I have to do it every time ?
reset 1
press F5
break (after the box finish its diagnostics)
go= 43089E (is a PH6 Board)
reset
Many ?'s
I have one purchase, does it supposed to clear to 0 ? ohhhh is unsent..
Do I have to cleared every time I watch a PPV ? or I could just
disable up link and connect cable in signal to "RF IN, and still watch all my channels ? (I haven't tryout) Please Can someone post steps for me...
1st disable uplink + order PPV.. ect
Why can I jump from 2 digits to 3 digits channels by pressing #'s (do I have to go one by one every time ? ) very slow.
Thank you all, you help is greatly appreciated (Newbie to DCT'S)
|
|
|
|
Post by usbbdm on Jun 11, 2005 9:59:13 GMT -5
OK, A little help around here.. My PPV NOT been cleared.. This are my steps.. (yes I did back up nvram the first time) do I have to do it every time ? reset 1 press F5 break (after the box finish its diagnostics) go= 43089E (is a PH6 Board) reset Many ?'s I have one purchase, does it supposed to clear to 0 ? ohhhh is unsent.. Do I have to cleared every time I watch a PPV ? or I could just disable up link and connect cable in signal to "RF IN, and still watch all my channels ? (I haven't tryout) Please Can someone post steps for me... 1st disable uplink + order PPV.. ect Why can I jump from 2 digits to 3 digits channels by pressing #'s (do I have to go one by one every time ? ) very slow. Thank you all, you help is greatly appreciated (Newbie to DCT'S) Pete, You need to knwo the firmware version before you run "go=" command. Each firmware starts at different address. |
|
pete
New Member
Posts: 7
|
Post by pete on Jun 11, 2005 10:06:19 GMT -5
Hey Boss my is Firmware "07.93, address=43089E
SO, I'm doing this
reset 1
press F5
break (after the box finish its diagnostics)
go= 43089E (is a PH6 Board)
reset
What Im I doing wrong ? The all process is with the TV on....
My Fault... ;D ppv Cleared.. ;D
|
|
|
|
Post by usbbdm on Jun 11, 2005 22:57:58 GMT -5
My Fault... ;D ppv Cleared.. ;D Good continue testing. |
|
|
|
Post by patsfan on Jun 12, 2005 9:05:55 GMT -5
anyone know the address for firmware version =7.72? i can't find it. I'm trying with this programming crap, but still suck at it. thanks.
|
|
|
|
Post by usbbdm on Jun 12, 2005 21:21:55 GMT -5
anyone know the address for firmware version =7.72? i can't find it. I'm trying with this programming crap, but still suck at it. thanks. You mean the clear PPV address for 07.72? If you post or email me the firmware, I can find it for you and post here. |
|
|
|
Post by patsfan on Jun 13, 2005 6:11:31 GMT -5
yes exactly. i will send it to you. thanks.
|
|
|
|
Post by usbbdm on Jun 13, 2005 10:55:57 GMT -5
yes exactly. i will send it to you. thanks. For 07.22 the address is 00430142. Do you mean you can not program your box? Try new software. It support Intel chip now. |
|
|
|
Post by patsfan on Jun 13, 2005 13:51:41 GMT -5
no i can program the box just fine, i'm just not very good with writting software and debbugging etc.  |
|
|
|
Post by adrianbv6 on Jun 17, 2005 4:40:36 GMT -5
yea i cant write the firmware either ....i have to ask mr fix to help me with that thanx a lot man
|
|
|
|
Post by usbbdm on Jul 1, 2005 12:31:39 GMT -5
There are two members already reported that after certain number of order clear, the PPV cannot order any more.
The clear PPV method here uses internal error fix routine in the firmware. But each time the clear routine is called; there is a block of memory used to tell the error. There might be a certain number of errors allowed, So after a few clears (5-6 times) you should consider use your earlier NVRAM to restore so it will give you rooms to clear more.
|
|
|
|
Post by patsfan on Jul 1, 2005 14:35:34 GMT -5
so ther error is generated by the nvram? i thought after got the error that i wrote back the firmware and nvram i originally dumped from the box. maybe i didn't. i'll try it again and see what happens.
|
|
